60'' Full-Auto Take Up Low Temp Large Format Hot Cold Seal Laminator Machine USA

Description

Upgraded 60'' Full-Auto Low Temp Wide Format Cold Laminating Machine
USA Stock, Fast shipping within 24 hours!
DOOR to DOOR Service！No Customs Troubles! 3 YEARS WARRANTY!
Buy with confidence! You buy, we assume all responsibility!
Kindly Note: Not Include the Air Compressor !!!
Details:
This 60" Full - auto Low Temp Wide Format cold laminator with Stand can be widely used for pre - masking vinyl graphic, mount prints on substrate, over laminating inkjet prints and so on.
The cold laminator is used to after printing. Available for photographic, Ad. Shop and copy shop to do lamination work, adding a protective layer on books cover, photographic, color pages, documents, charts, drawings, indoor advertising products, etc.
This laminator 1600C6+ is low heated cold laminator with liner and without liner, a wide range of application.
It can be used both cold laminating and hot laminating with low temperature, to strip coil backing paper,to roll picture automatically.
Especially when work in hot laminating conditions,it will improve the coating effect by heating the roller,.
It’s multiple-function,easy operation and high efficiency.
Single side lifting roller, easy to adjust the open height of roller (the laminating thickness). Support roll to roll operation, which saves labor.
Good color reducibility and light transmittance, free of bubbles and snowflake point!
Model
SEC-010
Maximum Laminator Width
1520mm (60")
Roller’s Diameter
130mm (5")
Maximum Laminating Thickness
25mm (0.99")
Maximum Heating Temperature
when hot laminating, the temperature is 50~60 degree, the highest
temperature is 60 degree.
Laminating Speed
From
0 to 10m (393")
per minute
Preheating Time
5 - 10mins
Power Consumption
0.3 - 0.5KW / h
Power Input
2200W
Height Adjust
Single side lifting link
Motor Forward / Reverse
Yes
Floor Stand
Yes
Auto Rewind Liner Pickup
Yes
After Laminating Pickup
Yes
Emergency Stops
Yes
Safety Photocell
Yes
Power Supply
AC110V, 50 / 60Hz
Features:
Adopts low temperature cold laminating, mainly used to solve the issue that cold laminated images are hazy.
Stainless steel feeding table
130mm (5") upper rubber roller
Auto – take – up system
Anti – tilt and anti – fold device (Origin)
Pressure and height adjust hand wheel
Infrared temperature control device
Detail:
Control Panel using Instruction:
Preset temperature: Find out hot/cold framed switch, choose the "hot ", temperature display screen will light up, the left number is preset temperature, the right number is roller temperature, press “■ SET”key and then through “▲ UP” and“▼
DOWN” adjust preset temperature, after adjust it and press“■ SET”key confirm it. when cold film, the preset temperature is 50 ℃ .,the max temperature is 50 ℃.According to the viscosity of the glue, and adjust preset temperature.
Turn: This machine don’t have continuous reverse function;
In the "continuous" state it only can " turning";
In the "point move" state, through the pedal switch can "turning" or "reverse".
Governor knob: clockwise to grow speed, counter-clockwise to slow down; Please select the appropriate speed to ensure the laminating effect, when stop coated please select "point move".
General Using and installation method
Note：The hex nuts must be tighten! If loose will appear heating power electric spark change,and broken wire and other components.
Film laminating
Laminating work is an extremely fine, technical stronger work, for beginners should have experience in the technicians under guidance of Membranae tectoria work, the below only show the general operation.
Preheating ready to work:
1. Fall down tne upper nip roller;
2. Press the "continuous" and "turning" switch, governor rotate to the "1";
3. Open the main switch;
4. Open the "hot" switch and et the heat temperature which we required, then nip roller began to heating. Hot laminating, the preset temperature is 90 ℃ , when low temperature/cold laminating, the preset temperature set to 45 ℃ (to working temperature need about 10-20 minutes)
5. Take out a roll of film and install into material roller, then let roll into material feeding roller scaffold and pulling the film with the hand, shall ensure the appropriate resistance,through the next to the damping handwheel adjust it.
6. Let framed chart scroll in carton, then packed in rewinding stent and fixed them.
The general questions and methods:
Problem
Control panel have no electricity
Method:
Check the power and emergency button
Problem Don't turn
Method:
Lift a little the upper roller
Adjust friction
Tighten sprocket key
Contact with motor or governor
Problem
Laminated paper isn't clear and have white point
Method:
Increase roller temperature
Clean the dust
Contact suppliers to replace film
Problem
laminated paper have pleated bubbles
Method:
Adjust roller force
Put paper in 90 angle into rubber roller
Increase speed and reduce temperature
Problem
Film fold
Method:
Adjust material-roller's resistance
Adjust to the required temperature
Package:
The laminator comes with 2Pcs of heating glass tube, 1Pcs is on the machine, 1Pc is in
another package. We send the spare 1Pc of it just in case of any damage during the
shipping.
If the one on the machine damaged, please use the spare 1Pc replace it.
We will not accept any complaint of the tube damaged.
Machine Dimension
74" x 27" x 45" (1880mm x 680mm x 1140mm)
Machine Weight
280lb (140kg)
Package
Fumigation free package
Packing Size
81" x 28" x 28" (2060mm x 710mm x 720mm)
Gross Weight
441lb (200kg)
Table 1: Accessories
Term
Quantity
Notice
Backing sheet reception roll
1
Feeding roll
1
Film roll
1
Black rubber beam weight
1
Finished products roll
1
Hand wheel
1
Rubber mat
1
Left support of feeding roll
1
Right support of feeding roll
1
Fuse
4
2A/7A
Video
1
Application:
Applying to indoor and outdoor car sticker,photo and video,rimless no painting mounting and so on.
SHIPPING
1. Items will be shipped within 1-3 business day after clear payment.
2. The shipping time varies. If by FedEX, DHL,or UPS, 3-4 business days to USA,5-7 business days to other most countries.
If by e-packet,7-15 days to USA,and 2-4 weeks to other most countries.
3. If you have not received your shipment within 30 days from payment, please contact us. We will track the shipment and get back to you in 24 hours.
PAYMENTS
1. We accept: Paypal, Please contact us if you may need some other payment method.
2. Please list your special requests in message after payment. (color, packages, etc.)
3. We ship to your eBay or Paypal address. Please make sure your eBay and Paypal address is correct before you pay.
Feedback
1. If you have any  problems or concerns to your order or products, please message us and  give us a chance to assist before you leave negative feedback.
2. We believe that we can produce a positive outcome to any situation to earn your likes.
3. Your satisfaction is guaranteed.
Return
1. If the item you  received is damaged or defective, please contact us, we will replace you new one or give you a refund, will do our best to help you, please let's know first.
2. All return items should be original package within 30 days after you received it. We are not responsible for the cost of shipping-back.
3. Please feel free to contact us if anything problem about the  transaction, We are sincere seller, I am always here to resolve any  problem for you. thank you for contact.